Product Details:
Payment & Shipping Terms:
|
Speed: | High Speed | Certification: | CE, ISO9001 |
---|---|---|---|
Packing: | Export Carton , Pallet | Number Of Poles: | 2 |
Excitation Mode: | HB-Hybrid | Application: | CNC Machine |
Two Phase Digital Hybrid Stepper Motor Driver For CNC Machine
Descriptions
The CW422C is a new generation digital 2-phase stepper motor driver, based on a 32-bit DSP processor, combination of the anti-resonance, low noise, micro-step and low temperature rise technology significantly improve the performance of the stepper motor, has low noise, small vibration, low temperature rise and high-speed torque. The driver use online adaptive PID technology, without manual adjustment can be automatically generated optimal parameters for different motors, and achieve the best performance.
Supply voltage range from 18VDC to 40VDC, suitable for driving various 2-phase hybrid stepping motors which phase current below 2.2A. The microstep can be set from full step to 6400steps/rev and the output current can be set form 0.5A to 2.2A; with automatic idle-current reduction, self-test, overvoltage, under-voltage and over-current protection.
Features
Applications
Suitable for a variety of large-scale automation equipments and instruments. For example: labeling machine, cutting machine, packaging machine, plotter, engraving machine, CNC machine tools and so on. It always performs well when applied for equipment which requires for low-vibration, low-noise, high-precision and high-velocity.
Parameter | Min | Typical | Max | Unit |
Input Voltage(DC) | 18 | 24 | 40 | VDC |
Output current | 0 | - | 2.2 | A |
Pulse Signal Frequency | 0 | - | 75 | KHZ |
Logic Signal Current | 7 | 10 | 16 | MA |
Current setting
Peak | SW1 | SW2 | SW3 |
Default | on | on | on |
0.5A | off | on | on |
0.7A | on | off | on |
1.0A | off | off | on |
1.3A | on | on | off |
1.6A | off | on | off |
1.9A | on | off | off |
2.2A | off | off | off |
Standstill Current Setting
SW4 is used for standstill current setting. OFF meaning that the standstill current is half of the dynamic current; and ON meaning that standstill current is the same as the selected dynamic current. Usually the SW4 is set to OFF, in order to reduce the heat of the motor and driver.
Microstep Setting
Step/Rev | SW5 | SW6 |
Default | on | on |
1600 | off | on |
3200 | on | off |
6400 | off | off |
Control signal Connector
Control Signal connector | |
Name | Description |
PUL+ | Pulse signal positive |
PUL- | Pulse signal negative |
DIR+ | Direction signal positive |
DIR- | Direction signal negative |
ENA+ | Enable signal positive, usually left unconnected(enable) |
ENA- | Enable signal negative, usually left unconnected(enable) |
Power and Motor Connector
GND | Power Ground |
+VDC | Power supply, +18~+40 VDC |
A+ | Motor phase A |
A- | |
B+ | Motor phase B |
B- |
Control Signal Connector Interface
Figure1: Common-Anode
VCC | R |
5V | 0 |
12V | 680Ω |
24V | 1.8KΩ |
4. Problems and Solutions
problems | Possible cause | solutions |
Motor is not rotating | No power supply | Check the power supply |
No control signal | Check the control signal | |
The driver is disabled | Don’t connected the enable signal or enable the driver | |
ALM lights | Supply voltage is too high or too low | Check the supply voltage |
Motor line short-circuit | Check motor lines eliminate the short-circuit | |
Motor line wrong connect | Check the motor wiring | |
Motor or drive failure | Replace the motor or drive | |
Motor rotates in the wrong direction | Motor phases connected in reverse | Reverse the phases line |
Motor line break | Change the phases are connected | |
Inaccurate Position | The Micro steps set incorrectly. | Set the correct segments |
The motor load is too heavy. | Increasing the current | |
Control signal is interfered | Eliminate interference | |
Motor Stalled | Power supply voltage too low | Increasing the supply voltage |
Accelerating time is too short. | Extend the acceleration time | |
Current setting is too small | Increasing the current | |
Motor torque is too small | Replace the motor |
5. Mechanical Specifications (unit: mm(inch),1 inch = 25.4mm)
Contact Person: Elaine Yang
Tel: +8615995079433